Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
Listed here in the next paragraph you will discover some dependable content in regards to How to Install a Bathtub Yourself.
Mounting a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately tough job. If the old bathtub is conveniently easily accessible, the job can relocate immediately; if you need to open up a wall surface to eliminate the old tub as well as position the new tub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a specialist plumber to make tube connections.
This short article will help you mount a brand-new bath tub in your shower room if you have actually already purchased a new tub and also do not need to transform the setup of your previous supply of water pipes.
Your tools and also product checklist ought to comprise the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly bothersome due to the limited accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipes. When the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leakages and tighten them if required. Fill the bathtub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub must wait up until the bathtub has been made use of at the very least once as this will resolve it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet adapters. The former type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a stiff seal, causing the water to permeate the wall between the bathroom as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that content on Tools You Need to Install a New Bathtub while doing a search on the internet. Sharing is caring. Who knows, you could be doing someone a favor. Thanks for your time invested reading it.
View Report this page